Short answer: H1, H4 and H7 are not interchangeable. They share a 12 V halogen heritage and a similar glass envelope, but the base, pin count and beam design are different, so each one drops into a specific socket. H1 is a single-beam bulb used in projector low beams, fog lamps and auxiliary lamps; H4 packs both high and low beam into one base; H7 is the single-beam low-beam bulb found across most European and Korean cars. The socket stamped on your old bulb decides the fit, and Chedina manufactures error-free LED versions of all three. See the size chart, the H4 fitment page and the H7 fitment page for the exact models. C6 is different: C6 is Chedina LED's 36 W entry-level headlight series — a product model, not a socket code like H4 or H7.
At a Glance
| Socket | Base | Beam | Typical use |
|---|---|---|---|
| H1 | P14.5s | Single (low or fog) | Projector low beam, fog lamps, auxiliary / off-road spots |
| H4 | P43t (3-terminal) | Dual (high + low) | Older cars, motorcycles, pickups, 7-inch round headlamps |
| H7 | PX26d | Single (low beam) | European & Korean low beam; common on VW, BMW, Mercedes, Hyundai |
Why They Are Not Interchangeable
A bulb base is a physical key, not a suggestion. H4 uses a three-terminal P43t base because it carries two filaments; H7 uses a two-pin PX26d; H1 uses a slim P14.5s. None of them will seat in the other's socket, and forcing one damages the connector. Beyond the base, the beam is different: H4 must reproduce both beams plus a low-beam shield inside one bulb, which is why H4 LED upgrades are far more sensitive to chip placement than H7. An LED that looks bright on a garage wall can throw glare into oncoming traffic if the shield or chip position is wrong.
Never file, bend or 'adapt' a base to make a bulb fit. A wrong base that is forced in will not make proper contact, overheats, and can trigger CANbus errors or melt the connector. Replace like-for-like.
C6 Is a Product Series, Not a Socket Code
C6 is Chedina LED's 36 W / 6000 lm entry-level LED headlight series — a product model, not a socket code like H1, H4 or H7. When a listing or a comparison mentions 'LED H7, H4 and C6 bulbs', H4 and H7 identify the base that fits your headlamp, while C6 identifies the Chedina LED product family you order that base in. The C6 36 W / 6000 lm headlight is specified by socket: the same C6 series can be supplied as H1, H4, H7, 9005 or 9006.
| Term | What it identifies | How to choose |
|---|---|---|
| H4 | A standardized dual-beam socket (P43t) | Stamped on the old bulb or headlamp housing |
| H7 | A standardized single-beam socket (PX26d) | Stamped on the old bulb or headlamp housing |
| C6 | A Chedina LED product series, 36 W / 6000 lm | Pick the C6, then pick the socket your car uses |
So C6 and H7 are not alternatives you choose between — you choose both. A C6 built on an H7 base is simply a Chedina C6 in H7 fitment. The same naming applies across our H4 range and H7 range. If a supplier lists C6 next to H4 and H7 without a socket, ask which base the C6 bulb uses before you order.
Which One Does Your Car Take?
- Read the code on the old bulb — it is stamped on the metal collar or glass, not on the plastic connector.
- Check the headlamp housing; many are embossed with the socket code.
- Confirm the model year and trim. The same nameplate can switch from H4 to H7 across a generation.
- If you see 'H4', you need a dual-beam LED. If you see 'H7' or 'H1', you need a single-beam LED for that specific base.
Upgrading to LED and CANbus
LED draws a fraction of the halogen current, which is exactly why some cars throw a bulb-out warning after an upgrade. If your vehicle is CANbus-monitored (most built after ~2005), choose an error-free, decoder-equipped LED. Our CANbus guide explains the failure mode and the fix, and our DOT vs ECE guide covers the paperwork different markets ask for. Browse the full headlight range to match the exact socket.
Can I use an H7 bulb in an H4 socket?
No. H4 uses a three-terminal P43t base and carries both high and low beam; H7 uses a two-pin PX26d base for a single beam. They are physically different — use the H4 range or the H7 range according to the marking on the old bulb.
Is H1 the same as H7?
No. H1 is a slim P14.5s single-beam bulb used in projectors and fog lamps; H7 is a PX26d single-beam bulb for European/Korean low beams. Different base, different position — they do not interchange.
Which should I stock first as a distributor?
It follows the vehicle parc: H7 for European and Korean cars, H4 for older fleets, motorcycles and pickups, H1 for projector and fog applications. Send us your vehicle list and we will propose the mix before you commit — see our OEM/ODM page.
What is a C6 LED bulb?
C6 is Chedina LED's 36 W / 6000 lm entry-level LED headlight series — a product model, not a socket code. Unlike H1, H4 or H7, which describe the physical base, C6 describes the Chedina LED product family. See the C6 36 W LED headlight, which can be ordered in H1, H4, H7, 9005 or 9006 fitment.
Is C6 the same as H7 or H4?
No. H7 (PX26d) and H4 (P43t) are standardized socket codes; C6 is a Chedina LED headlight series that is built in those sockets. A 'C6 H7' is a Chedina C6 bulb on an H7 base. Always confirm both the series and the socket before ordering.
Shop LED headlight bulbs by size
Wholesale buyers order by socket, not by series code. Pick a base to see the Chedina models listed for it, with specs and a quote path — and confirm the exact base before ordering.
Related reading
Short answers to the questions buyers ask us most.
